Fall Sale! 🎉 Save $100 on Electric Trikes
+ Tax-Free in Most States!
Grab your e-trike before the offer ends!

Adjusting the Hydraulic Brake Reach on Your Polar Electric Trike

by Perraro Electric Bike in Ebike Brakes

Introduction: Ensure a comfortable and secure ride by customizing the brake lever reach on your Polar Electric Trike for seniors. Follow this simple guide to tailor the hydraulic brake system to your needs.

Tools Required:

  • 2 mm Allen Wrench

Instructions:

  1. Initial Setup: Arm yourself with the 2 mm Allen wrench, the only tool necessary for this task.

  2. Accessing the Adjustment Point: Find the imbus screw beneath the brake lever. Loosen it just enough to permit the lever screw for adjustments.

  3. Making the Reach Adjustment:

    • Identify the small reach adjustment screw within the interior of the brake lever.
    • Insert your 2 mm Allen wrench into this screw.
    • For a closer grip, rotate the screw counter-clockwise.
    • For a wider grip, twist the screw clockwise.

  4. Refining the Adjustment:

    • Proceed with small increments, checking the lever feel with each adjustment.
    • Once the reach suits your preference, halt the adjustments.

  5. Securing the Lever:

    • Re-tighten the imbus screw to ensure the brake lever's position is stable and secure.

  6. Testing the Adjustment:

    • Compress the brake lever to check for proper brake engagement and a comfortable reach.

  7. Final Safety Check:

    • Take a cautious ride to verify the brakes' responsiveness and to confirm the adjustment enhances your riding comfort.

Conclusion: Your Polar Electric Trike is now customized for optimal control. Remember, safety is paramount; always perform adjustments in a risk-free setting and test thoroughly before setting out.

For any uncertainty, or if you prefer a professional touch, please seek assistance from a certified bike mechanic.

Visual Guide: Adjusting the Hydraulic Brake Reach on Your Polar Electric Trike

Safety Reminder: Before embarking on your next journey, ensure all adjustments are secure and fully functional.

If you have any inquiries or need further assistance, feel free to contact our support team at support@perraroelectricbike.com or call us at (949) 414-8003.

Your safe and enjoyable riding experience is our top priority!

Related Posts

Mechanical brake lever replacement guide for ebike

To replace a mechanical brake lever on your ebike, particularly if you're dealing with a Perraro Electric Bike or similar, you'll need to follow a detailed process. This guide is intended for those with mechanical brake systems. If your bike has hydraulic brakes, you'll need to refer to a different guide. Tools Needed: Flat head screwdriver Isopropyl alcohol Paper towel Flat side cutters 3 mm Allen wrench 5 mm Allen wrench Torque wrench with 3 mm and 5 mm Allen bits Zip ties Replacement brake lever (specific to your ebike model) Steps to Replace the Right Brake Lever: 1. Prepare the Bike Turn off the bike, remove the battery, and press the MODE or Power button to discharge remaining power. 2. Remove the Handlebar Grip Use a flat head screwdriver to pry off the grip end cap. Twist and pull the grip off. If it's tight, apply a bit of rubbing alcohol between the grip and handlebar as a lubricant. 3. Remove the Throttle (For Right Brake Lever Replacement) Trace the throttle cable to its connector, snip any zip ties, and unplug the connector. Use a 3 mm Allen wrench to loosen the throttle clamp bolt and slide off the throttle and spacer, noting the spacer's orientation for reassembly. 4. Remove the Old Brake Lever Add slack to the brake cable at the caliper using a 5 mm Allen wrench. Align the barrel adjuster and lock nut slits with the slot on the brake lever housing. Remove the brake cable from the lever and unplug the brake connector. Loosen the brake lever clamp bolt with a 5 mm Allen wrench and slide off the old lever. 5. Install the New Brake Lever Slide the new brake lever onto the handlebar, adjusting it to match the angle of the other lever. Tighten the clamp bolt with a 5 mm Allen wrench and torque as specified in your Owner's Manual. Reconnect the brake connector, ensuring notches and pins are properly aligned. 6. Reinstall the Brake Cable Line up the barrel adjuster and lock nut slits with the lever housing slot. Insert the cable stop into the lever mount and thread the cable through the slits. Secure the cable housing in the barrel adjuster and tighten the lock nut against the lever housing. 7. Adjust Brake Cable Tension Pull the brake cable taut at the caliper and tighten the pinch bolt with a 5 mm Allen wrench, torquing to the specification in your Owner's Manual. Test the brake lever's reach and adjust if necessary. 8. Reinstall the Throttle (If Removed) Slide the throttle and spacer onto the handlebar, ensuring correct spacer orientation. Tighten the clamp bolt with a 3 mm Allen wrench and torque as specified. Reconnect the throttle connector, aligning notches and pins. 9. Reinstall the Handlebar Grip Apply a small amount of isopropyl alcohol to the handlebar and slide the grip into place. Reinstall the end cap. Ensure the grip is secure once the alcohol dries. 10. Final Touches Replace any snipped zip ties to secure the cables neatly. Reinstall the battery and perform a thorough test of the bike before riding. Notes: If replacing the left brake lever, the process is similar, but you won't need to remove the throttle. Always refer to your ebike's specific Owner's Manual for torque values and other model-specific instructions. Regular maintenance and checks are crucial for ebike components, especially for bikes with mechanical brakes, as they may wear out faster than those on non-motorized bikes. This guide should help you safely and effectively replace a mechanical brake lever on your ebike. If you have any inquiries or need further assistance, feel free to contact our support team at support@perraroelectricbike.com or call us at (949) 414-8003.

Learn more

Hydraulic Brakes Replacement Guide for E-Bikes

Replacing hydraulic brakes on an e-bike can seem daunting, but with the right tools and guidance, it's a manageable task. This guide is designed to help you replace the hydraulic brakes on your e-bike, ensuring you can continue to enjoy safe and responsive braking. Remember, due to the added weight and speed capabilities of e-bikes, their brakes may wear out more quickly than those on traditional bikes, necessitating more frequent service. Tools You'll Need: Bike repair stand or lift Flat-side cutters Isopropyl alcohol Paper towels Flat-head screwdriver Allen wrenches (2 mm, 2.5 mm, 3 mm, 4 mm, 5 mm) Torque wrench Zip ties Brake pad separator (or a large, flat-head screwdriver) Preparation: Safety First: Turn off the bike, remove the battery, and discharge remaining power by holding the Power button. Documentation: Take photos of the current brake setup for reference during reassembly. Identify the Caliper: Determine which caliper (front or rear) needs replacing. The rear caliper is connected to the right brake lever, and the front to the left. Removal of Old Components: Caliper Removal: Use a 5 mm Allen wrench to remove the bolts securing the caliper to the frame or fork. Brake Hose Removal: Carefully remove the brake hose from its routing on the bike, cutting zip ties where necessary and using appropriate Allen wrenches to detach it from any clips or brackets. Handlebar Preparations: Depending on your e-bike's handlebar setup, you may need to remove grips or the throttle to access the brake lever. Use a flat-head screwdriver and Allen wrenches as needed to remove these components. Brake Lever Removal: Disconnect the brake lever from its cable and remove it from the handlebar using a 5 mm Allen wrench. Installation of New Components: Install New Brake Lever: Slide the new brake lever onto the handlebar, adjusting its angle to match the opposite lever, and secure it using a 5 mm Allen wrench. Ensure the clamp bolt is torqued to specifications. Route and Secure Brake Hose: Properly route the new brake hose along the frame or fork, securing it with zip ties or clips as necessary. Be careful to avoid any sharp bends or kinks in the hose. Caliper Installation: Position the new caliper over the rotor, ensuring the brake pads are correctly aligned. Insert and partially tighten the caliper bolts to allow for adjustment. Align the Caliper: Squeeze the brake lever to align the caliper, ensuring even spacing between the brake pads and rotor. Tighten the caliper bolts and check for smooth, rub-free rotation of the wheel. Connect Brake Cable: Reconnect the brake cable to the lever, ensuring a secure and correct connection. Reassemble Handlebar Components: If removed, reinstall the throttle and grips, ensuring they are securely fastened and positioned for comfortable operation. Adjust Brake Lever Reach: If necessary, adjust the brake lever reach to ensure comfortable and effective braking without the lever contacting the handlebar grip. Final Checks: Replace any cut zip ties and secure all cables. Reinstall the battery and perform a thorough test of the bike, including the brakes, before riding. Important Tips: Never Disconnect the Brake Hose: The brake set (lever, hose, caliper) is a sealed system. Disconnecting any part can lead to fluid loss and air entering the system, compromising brake performance. Work with Care: Hydraulic systems are sensitive to air bubbles and contaminants. Keep the system closed as much as possible and work in a clean environment. Brake Fluid: If any brake fluid is lost or contaminated during the process, the brake system may need to be bled. This is a more advanced procedure and may be best left to a professional if you're unsure. Safety Checks: After completing the brake replacement, it's crucial to perform a series of safety checks before taking your e-bike out for a ride. Ensure that all bolts are tightened to the manufacturer's specifications, the brake levers are functioning smoothly, and there is no rubbing between the brake pads and rotor. Test the brakes at low speed in a safe area to confirm they are working correctly. Replacing hydraulic brakes on an e-bike can significantly improve your riding experience and safety. However, if at any point you feel unsure about the process, consult a professional mechanic to avoid any potential issues. If you have any inquiries or need further assistance, feel free to contact our support team at support@perraroelectricbike.com or call us at (949) 414-8003.

Learn more

Hydraulic Brakes Adjustment Guide for E-Bike

Experiencing brake noise or rubbing on your electric bike (e-bike) or electric trike? It's not uncommon, especially during the initial break-in period, for new brakes to exhibit some noise or slight rubbing. However, if this persists beyond 25-50 miles, it's time to adjust your hydraulic brakes to ensure optimal performance and safety. This comprehensive guide is tailored for e-bike and electric tricycle owners, covering everything from ensuring proper wheel placement to caliper centering and brake lever adjustment.  If your brakes are new, click HERE to complete the bedding-in brakes process. Preparing Your Electric Bike or Trike for Maintenance Before diving into the adjustments, ensure your e-bike or electric trike is ready for maintenance. Turn off the power, remove the battery, and press the Power button to discharge any residual power. Remember, never flip your e-bike or electric trike when working on hydraulic brakes to avoid introducing air into the brake lines, which could lead to brake failure. Instead, use a bike repair stand or lift. Tools You'll Need: Bike repair stand or lift 2mm and 5mm Allen wrenches Torque wrench 18mm wrench Flat side cutters A sheet of paper Step 1: Check the Wheel Position Ensure the wheel is fully seated in the frame dropouts. An improperly seated wheel can cause the brake rotor to rub against the brake pads, creating noise. For front wheels, adjust the quick release lever, ensuring it's properly tensioned. For rear wheels on your electric bike or electric trike, use an 18mm wrench to adjust and properly seat the wheel in the dropouts. Step 2: Inspect the Brake Rotor Wearing protective gloves to avoid contact with the rotor's sharp edges, spin the wheel to ensure it moves freely with minimal contact between the brake pads and rotor. Use a sheet of paper behind the brake caliper to check if the rotor is true (straight). A wobbly or damaged rotor may need replacement. Step 3: Center the Brake Caliper Loosen the caliper bolts with a 5mm Allen wrench and manually align the caliper so the brake pads are parallel to the rotor. While holding the brake lever, retighten the bolts. Spin the wheel to check for rubbing. If necessary, make minor adjustments until the brake pads no longer rub against the rotor. Step 4: Adjust the Brake Lever Reach Finally, tailor the brake lever reach to your comfort using a 2mm Allen wrench. Ensure there's enough space between the brake lever and the handlebar grip to prevent the lever from touching the grip when fully applied. This is crucial for ensuring your e-bike or electric trike's brakes function effectively, preventing potential accidents. Conclusion Adjusting the hydraulic brakes on your electric bike or electric trike is crucial for maintaining optimal performance and safety. By following these steps, you can ensure a smooth and noise-free braking experience. Remember, if you're not confident in performing these adjustments yourself, it's always best to seek the expertise of a certified and reputable bike mechanic. Keep your e-bike or electric trike in top condition to enjoy the best possible riding experience. If you have any inquiries or need further assistance, feel free to contact our support team at support@perraroelectricbike.com or call us at (949) 414-8003.

Learn more

Leave a comment